Keurig 2.0 Won’t Turn on And The Screen isn’t Working

If your Keurig 2.0 coffee maker won’t turn on, the screen is also not showing anything, or the power button is not working and not brewing fresh coffee, then you are in the right place

We’ll give you all the possible solutions in this article that can fix this Keurig 2.0 won’t turn on and the screen isn’t working issue without going anywhere and provide a step-by-step guide to solving this problem.

First, let’s solve the blank screen issue

My Keurig 2.0 Has A Blank Screen

Two typical issues might cause your Keurig 2.0 screen to remain blank.

The first possibility is that a wire within the machine got loose. The second most typical issue is that the interior of the Keurig is excessively damp.

Keurig 2.0 Stuck on Preheating Mode

Sometimes there may be some other problems in your Keurig like your machine stuck on preheating mode, but it can be fixed easily.

A Wire Within The Machine Got Loose

When you turn your Keurig machine on, it makes some sound, but the screen remains blank. This happens because the wire inside the machine is loose, which joins the display to the electrical board. Fortunately, this is simple to fix:

Step 1: Unplug Your Keurig Machine

Remember to unplug the machine to prevent electrical dangers and shorting out the circuit board before beginning any repair work. Because safety is important.

Step 2: Remove the Top Lid Screws

Locate the screws on the lid’s bottom side. Remove these screws with a screwdriver and put them away.

Step 3: Lift the Top Cover Partially

Lift the top cover only halfway, it is sufficient to get access to the internal components without completely removing it. This will let you reassemble it easily later.

Step 4: Locate the Screen Connection

Now, loosen the front and side locks. Some latches will inevitably break off on the side, but it doesn’t matter as long as the one in front is still intact.

Then, place anything between the two components, such as a lighter, to make it easier to access the connection between the display and the circuit board.

Step 5: Remove and reconnect the screen connection

With the use of scissors, safely separate the main circuit board wire from the screen (the small white thing connected to the back of the screen). Then, firmly reattach the wire, making sure it is correctly positioned.

Step 6: Reassemble the Keurig Machine

Now carefully place the top cover back into place, making sure it’s fixed correctly in its place. Reinstall the screws that were removed before, and tighten them with the help of a screwdriver.

Step 7: Turn On The Keurig Machine

Now, after all the steps, plug the machine in and turn it on. Now the screen will be working again, and you can use your machine as normal.

Step 8: Test the Machine

First, choose your preferred brewing settings and place a coffee pod in the machine. Now start the machine by pressing the start button, just to check that it’s brewing coffee properly. If the machine is working correctly, the repair is finished successfully

After you have finished the repair procedure and confirmed that your Keurig coffee maker is operational, you may now sip your freshly prepared coffee.

If you face any issues with the screen in the future, then you can repeat all these steps to fix this issue.

The Inside of the Keurig 2.0 Is Damp

If the Keurig’s inside gets very moist, it can also lead to the screen getting blank, resulting in a faulty screen. There is also a straightforward solution to this problem:

Step 1: Open and Clean

  1. Lift the handle to open the Keurig.
  2. Take out the K-Cup holder.
  3. Clean the interior of the machine with a moist cloth to remove any accumulated coffee grounds or dirt.

Step 2: Plug In and Preheat

  1. Close and plug in Keurig. At this moment, the screen will remain white and unresponsive.
  2. To begin the preheating procedure, press the bottom-right corner of the screen.
  3. Wait for the water to begin bubbling. The machine is done preheating when the bubbling stops.

Step 3: Dispense Hot Water

  1. For dispensing hot water, push the Keurig button in the center of the screen. Keep in mind that the screen will still be blank at this time.
  2. Wait until the hot water is finished dispensing. Lift the handle to halt the procedure, if required.

Step 4: Reset the Machine

  1. Open the handle by lifting it, and keep it open for 2 to 3 minutes.
  2. Unplug the coffee maker, shut the handle and wait until 30 seconds
  3. Reconnect the machine. The screen must now be operational.

To fix this blank screen problem in your Keurig 2.0, it may take more than one attempt. If the problem remains after all these steps, then contact Keurig customer support for additional help.

The Power Button is Not Working.

If the screen becomes functional but nothing occurs when you push the little power button in the bottom right corner, you can attempt this solution.

  1. Put the K-Cup in the machine after opening the handle
  2. Keep your finger on the little power button.
  3. Now shut the handle while hitting the top of the handle.
  4. Repeat until the display functions normally again.

Final Words

It’s frustrating to face the issue of a blank screen or a power button that is unresponsive. particularly when you want a recently brewed cup of coffee.

However, as we mentioned in this article, you can easily fix these issues on your own by following the steps we have mentioned in the guide. It could be a loose cable connection, moist internal components, or a faulty power button.

If the problem remains after trying all the solutions mentioned in the article, then the best thing is to contact Keurig customer support for additional help

Meet Vishu Yadav, the coffee connoisseur behind With a barista background and a love for coffee, he explores diverse coffee cultures and brewing techniques. Join him for the latest trends, specialty roast reviews, and brewing insights on

Leave a Comment